Seat Bags

Named after the Italian word for Brick, Mattone is a water-resistant, ultra-compact seat bag that attaches to the rails using the BOA Closure System.  Unique zipper design allows it to be accessed while on the bike, or to open like a book when removed from the bike for easy access. Mattone is for the cyclist looking to carry a spare tube, CO2, multi-tool, and some cash in a discreet, water-resistant package. Internal divider holds ID, credit card, or cash while also protecting your tube from your multi-tool! Seat bag users fall into two categories: Seat Roll aficionados and seat bag users. Traditionally, seat bags have been simple open spaces that allowed content to jangle about, making noise and rubbing against each other. Often times a spare tube was pulled out of a seat bag to reveal it was more full of holes than the tube being replaced due to friction against a house key or multi-tool. With Mattone, we designed a layout similar to a book, where the bag can fully open to hold the tube and CO2 cartridge on one side, separated by a padded ballistic nylon 'page' separating it from the other side where you can store an inflator head, multi-tool, contact lens case, etc. The 'page' also contains a slot for a credit card, ID, money, or house key. The unique off-center Aquaguard Zipper allows the case to completely open and lay flat when off the bike, while also allowing easy access to the multi-tool and money/card slots when on the bike without risk of spilling all the contents of the bag. A high-friction Hypalon strap with BOA Closure completes the package. Making more than 15x the power of Velcro, the BOA Closure uses a ratcheting mechanism that will not creep or loosen even under the most extreme vibration and impact. This ensures the Mattone will remain 'high and tight' under your saddle until you need to access it...no swinging, swaying, or rattling...ever. - Exterior—Sleek black finish with reflective graphics - Interior—Hi-contrast red material with separate ID, credit card, or money flap - Interior Volume—Holds one inner tube, one CO2 cartridge, one tire lever (all of these components are sold separately and are not included) - BOA Closure System with open guide release on Hypalon retaining strap - YKK Aquaguard zipper - Outside Dimensions: 13cm x 8.5cm x 5.5cm - Volume: Approximately .61 L - Strap Measurements: 27cm x 4.5cm

Carry just the essential roadside/trailside tools with the MSW Tool Hugger. Sleeves are designed to fit tire levers, CO2, inflator, patch kit, multi-tool, and a tube (all sold separately). Works well standard saddle rails, or just toss it into a jersey pocket. - Durable Cordura outer layer - Seven elastic tool compartments - Hook and loop closures

A lightweight under-the-seat bag for carrying ride essentials. Every Seymour bag is created using Oceanweave – Axiom’s new lightweight and durable fabric made from reclaimed fishnet – to help reduce the amount of harmful plastics in our oceans. - Volume 1.3 L / 79 cu in - Weight 93g / 0.21 lbs - OCEANWEAVE 600D recycled fishnet polyester with waterproof polyurethane coating and a red interior liner to improve internal visibility - Lightweight Velcro saddle mounting system can be cinched down to ensure a quiet load - Zippered flap opening for easy access to bag contents while bag is on bike - Interior credit card / ID pocket - Ultra-visible 3M triangle logo - LED light clip

Plenty of room and durability to support you on epic rides. If being prepared is important the super cache can carry enough to accompany you on epic rides. - Water resistant 1000D material with YKK zipper - Interior division for all your essentials - Reflective logo, webbing to clip light - Angled straps achieve a low profile fit - No-snag Velcro and Amara leather limit abrasion

Want to bikepack without breaking the bank? Banjo Brothers to the rescue. A huge seat-mounted pack for bikepacking and commuting - no rack required. Usable capacity between 800 cu in and 350 cu in. 800 cu in (13L) – 22 x 7 x 6.25. Can be compressed down to 350 cu in when full capacity not needed. Rigid hull inside front of bag for secure support even when bag isn’t full. Removable waterproof liner. Requires a gap between saddle rails and fender of at least 8". - Weight: 2 lbs - Dimensions: 22.0"L 7.0" H x 6.25" W - Capacity: 800 cubic inches / 13L - Removable waterproof liner. - Requires a gap between saddle rails and tire of at least 8". - Imported

- Adventure ready saddle mounted removable drybag and holster system - Includes waterproof carry bag with air release valve to keep gear dry and compact - Bag easily slides in and out of holster without having to remove from bicycle - 15L measures 19.7

Thanks to the unique Seat-Lock attachment system, the Seat-Pack QR is quickly and securely mounted and just as speedily removed, completely residue-free. An adapter even enables the use of a dropper post, making the innovative Seat-Pack QR suitable for a variety of bikes. DETAILS Whether you're riding singletrack, mountain passes or gravel routes, with the waterproof Seat-Pack QR you are ready for every bike adventure. With the innovative and patented Seat-Lock attachment system and abrasion-resistant nylon fabric, the bag is super stable, quickly mounted and just as quickly removed without leaving any residue. And with the help of a special adapter of just 4.3 centimeter in width, this bag can even be used with a dropper post. The internal reinforcement and five compression straps ensure that the contents are packed tightly and securely. A valve with a handle strap helps to compress the pack volume, and the elastic cord on the outside allows for the attachment of additional gear. To prevent damage from tire contact, a protective plate is attached to the underside of the Seat-Pack QR, which also doubles as a fender. OTHER PRACTICAL FEATURES: - Our reflector ensures added visibility and safety - A daisy chain allows for the attaching of a rear light COMPATIBILITY NOTICE YOU CAN EASILY CHECK IF YOUR SADDLE IS COMPATIBLE: 1. The saddle rails must have a bend of at least 34°. 2. The seat post clamp must be at least 13mm from the middle of the bend in the saddle rail. There must also be at least 13mm from the middle of the bend to where the rail connects to the back of the saddle. 3. The bottom edge of the saddle (at the side) must be at least 14mm higher than the bottom edge of the saddle rail.